Non-Silicone Mold Release Formula 700

Home


	Product
	Mold Release Silicone Mold Release Formula 300 UL approved Silicone Mold Release 3S Silicone Mold Release Formula 800 UL approved Silicone Mold Release Formula 600 Non-Silicone Mold Release Formula 700 Non-Silicone Mold Release Formula ER-15 Non-Silicone Mold Release SL-32 Non-Silicone Mold Release Formula 701
	Lubricants Fusing Machinery Cleaner Lubricant AR-22 General Purpose Lubricant Silicone Lubricant
	Adhesive Sprays N Stick Formula 120
	Air Fresheners
	Contact Cleaners Easy Clean Formula 900 Solvent Cleaner Easy Clean Formula 900B Solvent Cleaner Resin Remover Formula 910 Concentrated Purging Compound Spot Remover SP-2 Spot Remover SP-3
	Grease Sprays
	Silicone Sprays Silicone Dry Spray P-33 Silicone Spray (Wet) P-34 Silicone Thread Lube and Release P-35
	Cutting and Tapping
	Anti-Corrosion Anti-Corrosion Preventive AR-118 Green White Anti-Corrosion Agent Formula 119
	Penetrating Oil
	PTFE Lubricants
	Spot Lifting Sprays
	Chain Lubricants Chain Lubricant Formula 110
	Ejector Pin Lubricants Ejector Pin Lubricant Formula 100

	Contract Packing
	New Products
	Distributors

Product > Mold Release > Non-Silicone Mold Release Formula 700

NON-SILICONE MOLD RELEASE

PRODUCT CODE : SL- 17

BRAND NAME : NON-SILICONE MOLD RELEASE FORMULA 700

DESCRIPTION
Non-Silicone Mold Release SL-17 was developed as a non-silicone release agent suitable for precision injection and compression moulding for thermoplastic and some thermoset materials. It is a vegetable base release agent for a drier, less oily releasing particularly for transparent plastic materials. It will eliminate any stress cracking and crazing when moulding polyethylene. It is good for moulding parts which require further processing such as silk screening, lacquer spraying, lamination, heat sealing and electroplating. It gives a clean finishing on the moulded parts. Some of the plastic materials that can be used with Formula 700 are : Acetal, ABS, Acrylic, Polyethylene, Polypropylene, Polysulfone and Nylon. This formulation does not contain ozone depleting chemicals and it is biodegradable. The release agent is a food approved material. This formulation is safe on solvent sensitive plastics and will not interfere with bonding. It is important for users to always test any release agent with a particular resin or polymer.

PRODUCT PROPERTIES
Paintable, suitable for metal hot stamping, permits ultrasonic welding of plastics parts.

Typical Physical & Chemical Properties
Specific Gravity (25°C)	: 0.7 (concentrate)
Flash Point	: < O degree C
Appearance	: Amber, transparent
Flammability	: Flammable
Operating Temperature	: 260°C max
Evaporation Rate	: Fast drying solvent

Direction of Use

Make sure the mold surface is clean.
Spray evenly from a distance of 15 to 20 cm to obtain good overage.
Do not overspray. Excessive spraying will not necessarily give better results.
Determine and tryout spraying distance for each different application.

Caution
Contents under pressure. Do not spray near any fire or sparkling point. Do not store or expose the aerosol container to temperature above 50°C. Do not pierce or burn the container. Use in well ventilated areas. Avoid breathing the vapor and do not over spray. Keep out of the reach of children.

28 September 2002

Email to friend